Insulation in Arlington, TX
Spray foam insulation in Arlington typically costs $2.25 to $5.75 per board foot for open-cell and $3.50 to $7.50 per board foot for closed-cell, depending on how much air sealing is needed first. The city’s 1970s through 1990s brick-veneer tract homes were insulated for cheap energy and cooling loads, not for today’s Oncor bills or the February 2021 cold snap. Call (218) 261-7714 for a written price before any work starts.
Why Arlington Homes Are Different
Arlington’s residential market is dominated by brick-veneer ranches and two-story tract homes built between roughly 1975 and 1995, mostly in north and south Arlington subdivisions. Those homes went in with R-11 wall batts and blown-in fiberglass attic insulation spec’d around R-19 at build. Thirty to fifty years later, the attic fiberglass in most of them has compacted to 3 or 4 inches of effective coverage, which lands somewhere near R-11. The ductwork in a large share of these homes runs through unconditioned attics that hit 150°F and higher in July and August. That means the insulation is not just old. It is actively working against the HVAC system, which has to push conditioned air through a superheated space before it ever reaches a bedroom register. On the flat North Texas prairie, there is no natural windbreak or tree canopy to soften the load. The sun hits the roof deck, the attic becomes an oven, and the ductwork bakes. In the older subdivisions of south and west Arlington, we routinely open an attic hatch and find original blown-in fiberglass compacted to roughly R-11, with ductwork running through it. One insulation upgrade in that configuration often shows up as a measurable drop on the homeowner’s next Oncor bill.
Our Main Arlington Services
Two jobs dominate the phones in Arlington: attic insulation retrofits and crawl space work. Both are defined by the same local reality: homes built to minimal cooling-load standards, decades of attic heat, and ductwork that has to move air through unconditioned space.
Attic Insulation in Arlington
Most Arlington calls start with a hot upstairs or a utility bill that climbs every summer. The fix is usually adding insulation to a compacted attic floor after sealing the air leaks first. We find original blown-in fiberglass flattened to 3 or 4 inches in homes spec’d for R-19 at build. Attic Insulation in Arlington work is our highest-volume job in the city.
Crawl Space Encapsulation & Vapor Barrier in Arlington
Arlington’s mixed-humid climate and flat terrain mean crawl spaces hold moisture for months. Brick-veneer homes with pier-and-beam foundations breathe humid air into floor systems, and that humidity migrates into the house. Crawl Space Encapsulation & Vapor Barrier in Arlington stops the moisture at the source.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Arlington
Spray foam insulation in Arlington is the highest-performance option for homes where the ductwork runs through an unconditioned attic. Spray Foam Insulation air-seals and insulates in a single pass, which matters when the attic reaches 150°F and the ductwork is baking in it. On a 1980s brick-veneer ranch with original R-11 attic fiberglass, moving to open-cell foam on the roofline changes the whole envelope.
Open-Cell Spray Foam
Signs you need it
Your upstairs rooms run 8 to 10 degrees warmer than downstairs in July, or your HVAC runs constantly without hitting the setpoint.
What it costs in Arlington
Open-cell spray foam in Arlington attics typically runs $2.25 to $4.50 per board foot at standard depths.
How we do it
We air-seal top plates and penetrations first, verify the framing is dry, then apply the foam to the designated depth and document the result with photos.
Closed-Cell Spray Foam
Signs you need it
You have a roof leak history, an unvented attic design, or you need the most R-value per inch in a tight roof deck.
What it costs in Arlington
Closed-cell foam in Arlington runs $3.50 to $7.50 per board foot depending on depth and access.
How we do it
We confirm the substrate is sound, apply closed-cell in passes to build the specified depth, then record the final thickness with a photo record.
Rim Joist Spray Foam
Signs you need it
Your floors feel cold in January, or you find dust lines and air movement where the foundation meets the framing.
What it costs in Arlington
Rim joist sealing and foaming in Arlington typically totals $1,200 to $3,800 for a standard ranch home.
How we do it
We clean the rim joist cavities, apply foam to seal and insulate each bay, and photograph every cavity before and after.
Garage Ceiling Spray Foam
Signs you need it
The room above the garage never cools properly, or the garage door stays hot to the touch after sunset.
What it costs in Arlington
Garage ceiling foam in Arlington typically runs $1,800 to $4,500 depending on square footage.
How we do it
We seal the garage ceiling penetrations, apply foam to the underside of the garage ceiling, and document the coverage.
What Spray Foam Insulation Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Open-cell spray foam | $2.25-$4.50 per board foot |
| Closed-cell spray foam | $3.50-$7.50 per board foot |
| Rim joist foam sealing | $1,200-$3,800 |
Is spray foam worth it in an Arlington attic with ductwork up there?
Yes. When ductwork runs through an unconditioned attic, moving the insulation to the roofline with spray foam puts the ducts inside the conditioned envelope. That stops the single biggest efficiency loss in Arlington’s 1970s to 1990s homes.
Does spray foam replace my old attic insulation?
It depends on the job. If we spray the roofline, the attic floor insulation becomes less relevant. If we spray the attic floor, the existing insulation is removed first, then foam is applied. Call (218) 261-7714 for a written price.
Blown-In Insulation in Arlington
Blown-in insulation in Arlington is the most common retrofit for homes with original fiberglass that has compacted to 3 or 4 inches. Blown-In Insulation goes in fast, covers uneven attic floors thoroughly, and brings an R-11 attic back up to R-38 or R-49. It is the backbone of the Arlington retrofit market.
Blown-In Cellulose
Signs you need it
Your attic fiberglass is compacted below the joist tops, or you feel temperature differences between rooms on the same floor.
What it costs in Arlington
Blown-in cellulose in Arlington attics typically runs $1,000 to $2,500 for a 1,000-square-foot attic.
How we do it
We air-seal the attic floor first, mark final depth, then blow cellulose to the specified R-value and document the final depth.
Blown-In Top-Up
Signs you need it
Your existing insulation is dry and clean but simply too thin, measuring under R-30 in an Arlington attic.
What it costs in Arlington
A top-up in Arlington typically runs $800 to $2,200 depending on the current depth.
How we do it
We measure the existing depth, calculate the gap to the target R-value, top up with blown-in material, and photograph final depths.
What Blown-In Insulation Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Blown-in cellulose attic | $1,000-$2,500 (1,000 s.f.) |
| Blown-in fiberglass attic | $1,100-$2,600 (1,000 s.f.) |
| Blown-in top-up | $800-$2,200 |
How much does blown-in insulation cost in Arlington?
Most Arlington attic jobs run $800 to $2,600, depending on square footage and whether air sealing is included. We always air-seal before we insulate, so the price reflects both steps. Call (218) 261-7714 for an exact written price.
Can you add blown-in insulation over my old Arlington fiberglass?
If the old fiberglass is dry, uncontaminated, and still holding some loft, we can top up over it. If it has compacted below R-11 and has rodent contamination, removal and replacement is the better path.
Radiant Barrier Installation in Arlington
Radiant barrier in Arlington is a heat-reflection layer installed under the roof deck to cut radiant heat gain into the attic. Radiant Barrier Installation addresses the exact problem that defines Arlington summers: roof decks that hit 150°F and radiate that heat downward into the attic and the ductwork running through it. It is one of the few retrofits that directly targets the cooling-load burden, not just the insulation value.
Attic Radiant Barrier
Signs you need it
Your attic is consistently 30 to 40 degrees hotter than the outside air in summer, even with adequate insulation on the floor.
What it costs in Arlington
Attic radiant barrier in Arlington typically runs $1,500 to $3,500 for a standard ranch home.
How we do it
We staple or fasten foil to the roof deck underside, leave a ventilation gap, and photograph the coverage before finishing.
Radiant Barrier Roof Deck
Signs you need it
You are replacing your roof, or your attic ductwork runs high near the roofline and bakes all summer.
What it costs in Arlington
Roof deck radiant barrier during a re-roof typically adds $0.35 to $0.90 per square foot of roof area.
How we do it
We coordinate with the roofing contractor to lay the barrier over the deck before shingles go on, then document the seam laps.
What Radiant Barrier Installation Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Attic radiant barrier | $1,500-$3,500 |
| Roof deck radiant barrier | $0.35-$0.90 per s.f. |
| Radiant barrier and ventilation | $2,200-$4,800 |
Does radiant barrier help in an Arlington attic with ductwork?
Yes. Lowering the attic air temperature reduces the temperature difference across the duct insulation. Ductwork that runs through a 120°F attic loses less cooling than ductwork in a 150°F attic.
Is radiant barrier a replacement for attic insulation in Arlington?
No. Radiant barrier cuts radiant heat gain but does not replace the resistance value of insulation. It works with the insulation, not instead of it. Call (218) 261-7714 for a written price on a combined job.
Insulation Removal & Replacement in Arlington
Insulation removal in Arlington is most often needed in attics where original fiberglass has compacted, absorbed rodent contamination, or been soaked by a roof leak. Insulation Removal & Replacement clears the problem material so the space can be air-sealed and re-insulated to current code. In Arlington’s 1970s to 1990s tract stock, this is often the only way to recover an attic that has never been touched since the day it was built.
Attic Insulation Removal
Signs you need it
Your attic insulation is reduced to dirty, compacted layers under R-11, or it has visible rodent tunnels and droppings through the material.
What it costs in Arlington
Attic insulation removal in Arlington typically runs $800 to $2,300 for a standard 1,000 to 1,500 square foot attic.
How we do it
We vacuum the old material out, bag it, and prepare the attic floor for air sealing before new insulation goes in.
Contaminated Insulation Removal
Signs you need it
You find rodent urine staining, nesting material, or a musty odor that gets worse when the AC cycles on.
What it costs in Arlington
Contaminated insulation removal in Arlington typically runs $1,000 to $3,500, with price driven by contamination level and attic size.
How we do it
We wear full PPE, remove and bag the contaminated material, sanitize the attic floor, and verify the space is clean before re-insulating.
What Insulation Removal & Replacement Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Attic insulation removal | $800-$2,300 |
| Contaminated removal | $1,000-$3,500 |
| Insulation replacement | $1,500-$4,000 |
How much does insulation removal cost in Arlington?
Most Arlington removal jobs run $800 to $3,500, depending on attic size, contamination, and accessibility. The written price we hand you before work starts includes the full removal scope. Call (218) 261-7714 for yours.
Do I need to remove old attic insulation before adding new in Arlington?
Not always. If the existing material is dry, uncontaminated, and still above roughly R-19, a top-up is usually appropriate. If it is compacted, wet, or contaminated, removal and replacement is the only way to fix the attic properly.
Attic Air Sealing in Arlington
Attic air sealing in Arlington is the work that has to happen before insulation goes in, and it is the reason most Arlington retrofits underperform when it is skipped. Attic Air Sealing closes the gaps around top plates, can lights, duct boots, and penetrations so conditioned air stops leaking into the attic. In a 1980s Arlington tract home, the blower-door test usually reads 3,500 to 5,000 CFM50 before sealing and drops substantially after.
Attic Floor Air Sealing
Signs you need it
Your upstairs is warm in summer and cold in winter, or your HVAC runs long cycles without hitting the setpoint.
What it costs in Arlington
Attic floor air sealing in Arlington typically runs $800 to $2,000 depending on attic size and penetration count.
How we do it
We pull back the insulation, seal the top plates and penetrations, then lay the insulation back and document every sealed area.
Can Light & Duct Boot Sealing
Signs you need it
You feel drafts around ceiling fixtures, or you find dust streaks and dark insulation around can light trims.
What it costs in Arlington
Can light and duct boot sealing in Arlington typically adds $200 to $700 on top of the main air sealing scope.
How we do it
We seal each fixture and boot to the drywall and framing with approved materials, then photograph the completed work.
What Attic Air Sealing Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Attic floor air sealing | $800-$2,000 |
| Top plate and penetration sealing | $600-$1,800 |
| Can light and duct boot sealing | $200-$700 |
Why does Arlington attic air sealing matter more than insulation?
Because air leakage moves heat through the envelope far faster than conduction through material. A fiberglass batt with air moving through it performs at a small fraction of its rated R-value. Seal first, then insulate.
Do you do a blower-door test before and after air sealing in Arlington?
Yes, on every applicable job. The before-and-after numbers are published with the job record so you can see exactly how much conditioned air the home was losing before and after sealing.
Wall Insulation in Arlington
Wall insulation in Arlington is the job most homeowners never think about, because the walls look finished and the thermostat still works. Wall Insulation matters in the city’s 1970s to 1990s brick-veneer stock because most of those homes were built with R-11 wall batts and nothing else. Add in the flat prairie exposure and the February 2021 cold snap that exposed how little those walls resist heat movement, and wall retrofits have become a regular Arlington call.
Drill & Fill Wall Insulation
Signs you need it
Your exterior walls feel cold to the touch in winter, or your heating bill spikes during any sustained Arlington freeze.
What it costs in Arlington
Drill and fill wall insulation in Arlington typically runs $1.50 to $3.50 per square foot of wall area.
How we do it
We drill small access holes in the exterior or interior finish, blow insulation into each stud bay, and patch and document the holes.
Interior Wall Soundproofing
Signs you need it
You can hear conversations through interior walls, or a home office or nursery needs real acoustic isolation.
What it costs in Arlington
Interior wall soundproofing in Arlington typically runs $1,200 to $4,500 depending on wall count and materials.
How we do it
We open the wall cavity from one side, install sound-dampening insulation, close the wall, and document the material placement.
What Wall Insulation Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Drill & fill wall insulation | $1.50-$3.50 per s.f. |
| Injection foam wall insulation | $2.00-$4.50 per s.f. |
| Interior wall soundproofing | $1,200-$4,500 |
Can you insulate the walls in my Arlington home without tearing out drywall?
Yes. Drill and fill and injection foam both install through small access holes that are patched when the job is done. The finished wall surface stays intact. Call (218) 261-7714 for a written price.
How do I know if my Arlington walls have insulation?
A thermal imaging inspection shows the wall cavities in real time. We include thermal imaging as part of a home energy audit, and the images are part of the documented record you receive.
Attic Cleaning & Rodent Proofing in Arlington
Attic cleaning in Arlington usually starts with a homeowner finding rodent droppings or hearing scratching at night. Attic Cleaning & Rodent Proofing clears the contamination, sanitizes the space, and closes the entry points so the problem does not return. In Arlington’s brick-veneer tract homes, the entry points are almost always the same: gaps at the eave line, unscreened gable vents, and HVAC penetrations through the roof.
Attic Cleanout
Signs you need it
You find rodent droppings, nesting materials, or chewed insulation in the attic, or a musty smell comes through the ceiling.
What it costs in Arlington
Attic cleanout in Arlington typically runs $600 to $2,000 depending on attic size and contamination level.
How we do it
We remove and bag the contaminated material, vacuum the attic floor, and prepare the space for sanitizing or re-insulating.
Rodent Proofing & Exclusion
Signs you need it
You hear scratching in the attic at dusk or dawn, or you find new droppings after cleaning.
What it costs in Arlington
Rodent proofing and exclusion in Arlington typically runs $400 to $1,800 depending on the number of entry points.
How we do it
We inspect the entire roofline, seal every entry point with exclusion materials, and photograph the sealed openings.
What Attic Cleaning & Rodent Proofing Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Attic cleanout | $600-$2,000 |
| Sanitizing and decontamination | $300-$900 |
| Rodent proofing and exclusion | $400-$1,800 |
How much does attic rodent proofing cost in Arlington?
Most Arlington exclusion jobs run $400 to $1,800, with price driven by the number of entry points and roof access. The written price covers every opening we seal. Call (218) 261-7714 for an exact figure.
Do I need to replace insulation after rodent cleanup in Arlington?
Usually. Rodent urine and droppings contaminate the insulation, and that contamination does not go away with sanitizing alone. The standard path is removal, cleaning, exclusion, then new insulation.
Home Energy Audit in Arlington
A home energy audit in Arlington is a diagnostic pass that measures how much air the home is losing, where it is losing it, and which fixes return the most per dollar. Home Energy Audit work in Arlington almost always points to the same findings: a leaky attic floor, underperforming insulation, and ductwork running through unconditioned space. The blower-door number tells the story in one figure.
Blower Door Test
Signs you need it
You want a single air-leakage number for the whole house, or you are comparing bids and want documented performance data.
What it costs in Arlington
A blower door test in Arlington typically runs $150 to $400 as a standalone reading.
How we do it
We pressurize the house with a calibrated fan, read the CFM50 number, and identify the largest leak paths with the pressure held.
Thermal Imaging Inspection
Signs you need it
You want visual proof of wall voids, missing insulation, or air leaks that cannot be seen with the naked eye.
What it costs in Arlington
Thermal imaging in Arlington typically runs $200 to $500 depending on scope and square footage.
How we do it
We scan the envelope with an infrared camera while the blower door runs, then mark and photograph every cold spot and leak path.
What Home Energy Audit Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Blower door test | $150-$400 |
| Thermal imaging inspection | $200-$500 |
| Full energy audit | $300-$900 |
How much is a home energy audit in Arlington?
A full audit in Arlington typically runs $300 to $900, depending on scope and whether blower door and thermal imaging are both included. Call (218) 261-7714 for a written price before any work starts.
What does a blower-door number actually tell me in Arlington?
It tells you the total air leakage in cubic feet per minute at 50 pascals of pressure. Most Arlington tract homes built from the 1970s to 1990s read between 3,500 and 5,000 CFM50 before sealing.
Brands We Service in Arlington
We stock and install materials from our brands, including Knauf, Rockwool, and CertainTeed. Most standard attic and wall materials are available for Arlington jobs within one to two business days, with no proprietary product lock-in.
Pricing for Insulation in Arlington, TX
| Service | Typical range in Arlington |
|---|---|
| Blown-in cellulose attic | $1,000-$2,500 |
| Blown-in fiberglass attic | $1,100-$2,600 |
| Open-cell spray foam | $2.25-$4.50 per board foot |
| Closed-cell spray foam | $3.50-$7.50 per board foot |
| Attic radiant barrier | $1,500-$3,500 |
| Attic insulation removal | $800-$2,300 |
| Attic air sealing | $800-$2,000 |
| Drill & fill wall insulation | $1.50-$3.50 per s.f. |
| Attic cleanout | $600-$2,000 |
| Home energy audit | $300-$900 |
Price moves up in Arlington when attics are cramped, contamination is heavy, or ductwork blocks access to the work area. Every job gets a written price before work starts, a written scope, and a written warranty under the Haven Standard.
Neighborhoods We Serve in Arlington
We work across the whole city, from the older south and west Arlington subdivisions to the newer far north communities. Most Arlington jobs can be scheduled within 7 to 10 days, with same-week slots often available.
- Dalworthington Gardens
- Pantego
- Southwest Arlington
- North Arlington
- West Arlington
Service Area - Cities Near Arlington
We also serve the surrounding metro. Same-day dispatch for Arlington jobs is coordinated from our Dallas-Fort Worth office, with crews serving the city locally. Nearby coverage includes Grand Prairie, TX, Fort Worth, TX, North Richland Hills, TX, and Dallas, TX.
Serving Arlington, TX - Our Local Coverage Area
We’re based in the Arlington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Arlington
Most insulation retrofit work in Arlington does not require a separate permit, but some jobs involving structural changes or certain commercial properties do. We confirm permit requirements for your specific address before the written price is issued.
Same-day and next-day estimate slots are available in most Arlington neighborhoods, depending on crew schedule. The estimate includes a written price, a written scope, and a free second opinion on any competing written estimate.
Yes. If your HOA requires approval for exterior access or work visible from the street, we coordinate with the association and document the approval before the crew arrives. The written scope covers exactly what will be done.
Call Topside Attic Insulation at (218) 261-7714 for a written price on any insulation job in Arlington. Every job starts with a written scope and ends with a documented photo record, and before-and-after blower-door readings are provided on every applicable air sealing or insulation retrofit.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 1-hour.
- 4You approve before work beginsNothing starts until you say go.
What Arlington Customers Say
"The winter gas bill dropped by about a third. They had estimated a quarter, so they under-promised."
- Genevieve R."Two other companies quoted to blow more insulation on top of what was there. These were the only ones who said the existing material had to come out first, and explained why."
- Clifford E."Fixed price, clean work, and they hauled the old material away as agreed."
- Todd M.