Insulation in Atlanta, GA
Spray foam insulation in Atlanta typically runs $2.50-$7.50 per square foot installed, with most full-attic jobs landing between $6,500 and $14,000 depending on whether you choose open-cell or closed-cell. Atlanta’s pre-WWII intown bungalows and 1990s-2000s OTP production homes create two very different retrofit problems, and the right insulation approach depends on which one you own. Call (218) 261-7714 for a written price before any work starts.
Why Atlanta Homes Are Different
Atlanta sits in IECC Climate Zone 3A, a mixed-humid environment where summer attic temperatures routinely exceed 140-150°F. That heat load, combined with inward moisture drive during the long cooling season, means vapor management matters as much as R-value here. The housing stock compounds the problem. Intown neighborhoods like Grant Park, Virginia-Highland, Candler Park, and Kirkwood are dense with 1910s-1940s craftsman bungalows and foursquares built with balloon or platform framing and no original wall insulation. Meanwhile, the OTP suburbs across Cobb, Gwinnett, and Cherokee counties are packed with 1,800-3,500 sq ft production homes built to 1990s-2000s Georgia code minimums, often just R-19 batts in the attic and minimal air sealing, now hitting their first major retrofit cycle.
Atlanta’s cooling season punishes these shortcomings. A 2,800 sq ft house in Alpharetta with builder-spec attic insulation can easily see its upstairs bedrooms run 8-12°F warmer than the main floor from June through September. The bonus-room-over-garage plans so common in these subdivisions make it worse: knee walls and floor decks were routinely left uninsulated or insulated incorrectly, turning those rooms into ovens by August. This is why we treat air sealing as a hard prerequisite on every Atlanta attic job, not an add-on. Insulation alone cannot fix a leaky thermal envelope.
Our Main Atlanta Services
Two services account for most of our Atlanta calls: attic insulation and crawl space encapsulation. Both are shaped by local conditions, and both are covered in depth on their own Atlanta pages, linked below.
Attic Insulation in Atlanta
Atlanta attics take a beating: 140°F summer deck temperatures, high humidity, and decades of settling or pest damage. Most intown bungalows have degraded or absent attic coverage, while OTP production homes are under-insulated to begin with. We start every attic job with air sealing of top plates, can lights, and penetrations, then bring the assembly up to a documented R-value with materials appropriate for the existing roof and framing. Read the full breakdown on our Attic Insulation in Atlanta page, including pricing and blower-door methodology.
Crawl Space Encapsulation & Vapor Barrier in Atlanta
Atlanta’s mixed-humid climate pushes moisture up from the ground all year, and standard vented crawl spaces here routinely develop condensation, mold, and rot. Homes in older intown neighborhoods often have dirt-floor crawl spaces never designed for modern indoor air quality. Our Crawl Space Encapsulation & Vapor Barrier in Atlanta page covers the full scope: vapor barrier, sealing, conditioning, and the moisture readings we document at walkthrough.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Atlanta
Spray foam insulation in Atlanta solves what blown-in alone can’t: unvented attic assemblies where the roofline itself needs a sealed, high-R air and vapor barrier. In a city where attic decks hit 150°F and humidity drives inward for six months a year, closed-cell foam at the roofline consistently outperforms simply topping up blown-in on the attic floor, especially in the bonus-room-over-garage plans common across Cobb and Gwinnett. Our Spray Foam Insulation service always includes air sealing first because foam without sealing wastes the product.
Open-Cell Spray Foam
Signs you need it
You feel air movement from attic hatches or can lights, and upstairs rooms run noticeably hotter than the main floor during Atlanta summers.
What it costs in Atlanta
Open-cell spray foam in Atlanta typically runs $2.50-$4.50 per square foot for a full attic roofline application.
How we do it
We seal all top plates, can lights, and penetrations first, then spray the roofline to the specified depth, and finish with a blower-door reading to document the change.
Closed-Cell Spray Foam
Signs you need it
You need an unvented attic assembly with a vapor barrier, or you’re conditioning a bonus room over the garage that registers extreme temperatures in August and January.
What it costs in Atlanta
Closed-cell spray foam in Atlanta runs $4.00-$7.50 per square foot on a roof deck application.
How we do it
We complete air sealing, spray closed-cell directly on the deck to the depth specified in the written scope, and record before-and-after blower-door numbers on the job documentation.
Rim Joist Spray Foam
Signs you need it
You feel drafts at the base of exterior walls or your crawl space pulls humid Atlanta air into the house year-round.
What it costs in Atlanta
Rim joist spray foam in Atlanta runs $3.00-$5.50 per linear foot for a standard 2×10 joist band.
How we do it
We seal each rim joist cavity with foam, document the locations with photos, and note the changes in the written record.
Garage Ceiling Spray Foam
Signs you need it
Bedrooms above the garage stay hot in summer and cold in winter despite attic insulation elsewhere in the house.
What it costs in Atlanta
Garage ceiling spray foam in Atlanta runs $2.50-$5.00 per square foot, depending on open-cell or closed-cell product.
How we do it
We air-seal the ceiling plane, spray foam across the deck, and provide a photo record of every layer before the final walkthrough.
What Spray Foam Insulation Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Open-cell attic roofline | $2.50-$4.50 per sq ft |
| Closed-cell attic roofline | $4.00-$7.50 per sq ft |
| Rim joist sealing | $3.00-$5.50 per linear ft |
Is spray foam worth the cost in Atlanta?
Yes for unvented attic assemblies and bonus rooms with extreme temperature swings. Closed-cell foam at the roofline creates a sealed thermal and vapor barrier that addresses Atlanta’s inward moisture drive directly. We document the performance change with blower-door readings.
Does spray foam work better than blown-in for Atlanta attics?
In many Atlanta homes, yes, especially for conditioned attics and bonus rooms. Blown-in on the attic floor leaves the roofline unsealed. For vented attics with intact air sealing, blown-in remains a strong lower-cost option. Call (218) 261-7714 for a written comparison.
Blown-In Insulation in Atlanta
Blown-in insulation in Atlanta costs $1.75-$4.50 per square foot installed for attics, and it remains the most common retrofit for intown bungalows that were built with no attic coverage or with settling material from decades past. For the 1990s-2000s OTP production homes sitting at R-19 or less, a blown-in top-up is often the single fastest improvement to cooling bills. Our Blown-In Insulation crew air-seals before any material goes down, because blowing over an unsealed attic floor in a Zone 3A climate wastes a measurable share of the R-value you paid for.
Blown-In Cellulose
Signs you need it
Your attic has thin, settled, or patchy coverage and your upstairs rooms run hot through Atlanta’s long cooling season.
What it costs in Atlanta
Blown-in cellulose in Atlanta runs $1.75-$3.00 per square foot, including air sealing of the attic floor.
How we do it
We air-seal top plates and penetrations, blow cellulose to the R-value specified in the written scope, and take final depth readings with photos.
Blown-In Fiberglass
Signs you need it
You’re replacing old, compressed fiberglass batts or topping up builder-spec attics that have only R-19 or less.
What it costs in Atlanta
Blown-in fiberglass in Atlanta runs $1.75-$3.50 per square foot for a standard attic top-up or full application.
How we do it
We seal the attic floor first, blow fiberglass to the documented R-value, and include a photo record of depth markers throughout the attic.
What Blown-In Insulation Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Blown-in cellulose attic | $1.75-$3.00 per sq ft |
| Blown-in fiberglass attic | $1.75-$3.50 per sq ft |
| Dense-pack walls | $2.50-$5.50 per sq ft |
How often should attic insulation be topped up in Atlanta?
Most Atlanta attics with builder-spec R-19 or R-30 benefit from a top-up within 15-20 years, sooner if pests or moisture have compressed the material. Air sealing should happen first, every time. Call (218) 261-7714 for a written price.
Does blown-in help with Atlanta humidity?
Insulation itself does not dry the air, but combined with proper air sealing it reduces the stack effect that pulls humid outdoor air into the house. For crawl space moisture, we address vapor barriers separately. The blower-door reading shows what changed.
Radiant Barrier Installation in Atlanta
Radiant barrier installation in Atlanta runs $1.50-$4.50 per square foot for attic deck applications, and it’s one of the few measures that directly targets the 140-150°F attic surfaces radiating heat down into living space all summer. In intown bungalows with dark shingle roofs and little attic depth, a radiant barrier can cut the heat transfer into the house before it ever reaches the insulation layer. Our Radiant Barrier Installation work is always paired with an attic ventilation check, because a barrier that traps heat without airflow can shorten shingle life.
Attic Radiant Barrier
Signs you need it
Your upstairs rooms heat up fast on sunny days and your attic temperature climbs above 140°F by early afternoon in summer.
What it costs in Atlanta
Attic radiant barrier in Atlanta runs $1.50-$3.00 per square foot for a standard deck installation.
How we do it
We confirm attic ventilation first, install the barrier across the deck or rafters, and document the surface temperatures before and after with a thermal camera.
Radiant Barrier Roof Deck
Signs you need it
You have a south- or west-facing roof plane that makes the adjacent rooms noticeably hotter than the rest of the house in summer.
What it costs in Atlanta
Radiant barrier roof deck work in Atlanta runs $2.00-$4.50 per square foot, depending on rafter access and roof pitch.
How we do it
We install the barrier directly against the underside of the deck with the required air gap, then photograph the completed sections and record the before-and-after temperature readings.
What Radiant Barrier Installation Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Attic radiant barrier | $1.50-$3.00 per sq ft |
| Radiant barrier roof deck | $2.00-$4.50 per sq ft |
| Radiant barrier with ventilation upgrade | $3.00-$5.00 per sq ft |
Do radiant barriers work in Atlanta’s climate?
Yes. Atlanta’s long, high-heat cooling season is exactly where radiant barriers show the largest measurable effect. They work by reflecting radiant heat before it reaches the insulation. Ventilation must be adequate, which we verify before installing.
Can I combine radiant barrier with spray foam in Atlanta?
Only in a conditioned attic assembly at the roofline where ventilation is not the mechanism for heat removal. For vented attics, we install barrier alongside proper ventilation, not foam. Call (218) 261-7714 and we’ll read the roof structure with you.
Insulation Removal & Replacement in Atlanta
Full attic insulation removal and replacement in Atlanta runs $2.00-$5.50 per square foot, and it’s the correct path when rodent contamination, old water damage, or decades of dust have compromised the existing material. Atlanta’s older intown homes often carry insulation installed in the 1950s-1970s that simply needs to come out before new work can begin. Our Insulation Removal & Replacement crew removes material with HEPA-filtered vacuum equipment, then re-seals and re-insulates the attic floor to a documented R-value.
Attic Insulation Removal
Signs you need it
Insulation is compressed, wet, mold-stained, or packed with dust and debris from decades of Atlanta attic exposure.
What it costs in Atlanta
Attic insulation removal in Atlanta runs $2.00-$3.50 per square foot, excluding new material install.
How we do it
We vacuum out the old material with HEPA filtration, clean the attic floor, and document the cleared surfaces before new insulation goes in.
Contaminated Insulation Removal
Signs you need it
You’ve had rats, squirrels, or raccoons nesting in the attic, or there’s visible mold and moisture damage on the existing insulation.
What it costs in Atlanta
Contaminated insulation removal in Atlanta runs $2.50-$5.50 per square foot, depending on the extent of contamination and attic access.
How we do it
We remove contaminated material under HEPA filtration, sanitize the affected decking, seal entry points, and issue a photo record of the completed removal before re-insulating.
What Insulation Removal & Replacement Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Attic insulation removal | $2.00-$3.50 per sq ft |
| Contaminated removal | $2.50-$5.50 per sq ft |
| Full removal and replacement | $4.50-$8.00 per sq ft |
Is it cheaper to remove old insulation or blow over it in Atlanta?
Blowing over is cheaper upfront when the existing material is dry, uncontaminated, and structurally intact. If pests, moisture, or compression are present, removal is the only route that doesn’t trap the problem underneath. A written inspection tells you which applies.
How long does attic insulation removal take in Atlanta?
Most Atlanta attics take one to two days for removal, depending on depth, access, and contamination level. Re-insulation is scheduled immediately after so the house isn’t left exposed. Call (218) 261-7714 for a written timeline.
Attic Air Sealing in Atlanta
Attic air sealing in Atlanta runs $1.00-$2.50 per square foot of attic floor area, and it is the single most cost-effective measure in a Zone 3A climate where conditioned air leaks out and humid outdoor air gets pulled in through the same holes. A bungalow in Grant Park or Kirkwood can easily be losing 30-40% of its conditioned air through top plates, can lights, and plumbing penetrations before anyone touches the insulation. Our Attic Air Sealing work always precedes insulation because sealing after insulation is put down is slower, messier, and less effective.
Attic Floor Air Sealing
Signs you need it
You feel drafts near attic hatches, or dust lines appear on insulation around light fixtures and wall top plates.
What it costs in Atlanta
Attic floor air sealing in Atlanta runs $1.00-$1.75 per square foot, depending on how many penetrations need work.
How we do it
We seal all top plates, plumbing and electrical penetrations, and framing gaps, then run a blower-door test to document the before-and-after CFM50 numbers.
Can Light & Duct Boot Sealing
Signs you need it
Recessed lights are warm to the touch in summer, or you can feel air moving around ceiling fixtures and supply registers.
What it costs in Atlanta
Can light and duct boot sealing in Atlanta runs $1.50-$2.50 per square foot when combined with floor sealing.
How we do it
We install rated covers over non-IC housings, seal duct boots at the drywall plane, and photograph each fixture before and after.
What Attic Air Sealing Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Attic floor air sealing | $1.00-$1.75 per sq ft |
| Can light and duct boot sealing | $1.50-$2.50 per sq ft |
| Full attic sealing with blower-door test | $1.75-$2.50 per sq ft |
Does air sealing make a real difference in Atlanta?
Yes. We measure it. A typical Atlanta bungalow might read 4,200 CFM50 on the blower-door before sealing and 2,100 after, a 50% reduction in air leakage. The pressure test is part of every applicable job and the numbers are in the documentation you keep.
Do I need air sealing before insulation in Atlanta?
Always. Blowing insulation over an unsealed attic floor is like putting a thicker blanket over an open window. For Atlanta’s humid cooling season, the sealing is a hard prerequisite, not an option. Call (218) 261-7714 to talk scope.
Wall Insulation in Atlanta
Wall insulation in Atlanta runs $2.50-$5.50 per square foot for drill-and-fill or injection foam, and it’s a job that comes up constantly in the intown bungalow belt where 1910s-1940s homes were built with no wall insulation at all. Those craftsman houses in Grant Park, Virginia-Highland, and Candler Park sit inside walls that are empty cavities, and Atlanta’s cooling load makes the thermal difference between rooms with and without wall insulation surprisingly large. Our Wall Insulation work reaches these cavities through small exterior or interior access points and fills them completely, eliminating the solar-driven heat gain that keeps intown bedrooms warm well after sunset in summer.
Injection Foam Wall Insulation
Signs you need it
Interior walls feel warm to the touch in summer, and rooms along unshaded exterior walls run hotter than interior rooms.
What it costs in Atlanta
Injection foam wall insulation in Atlanta runs $3.50-$5.50 per square foot of wall area, depending on cavity depth and access.
How we do it
We drill small access points, inject foam to fill the cavity completely, and finish with a photo record and the insulation density readings.
Drill & Fill Wall Insulation
Signs you need it
You own a pre-WWII intown home with no wall insulation, and energy bills spike during Atlanta’s cooling season.
What it costs in Atlanta
Drill and fill wall insulation in Atlanta runs $2.50-$4.50 per square foot, with cellulose or fiberglass fill options.
How we do it
We access each stud cavity, pack the fill to the specified density, and document every cavity with photos before patching.
What Wall Insulation Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Drill and fill wall insulation | $2.50-$4.50 per sq ft |
| Injection foam wall insulation | $3.50-$5.50 per sq ft |
| Interior wall soundproofing | $3.00-$6.00 per sq ft |
Can you insulate walls without opening the drywall in Atlanta?
Yes. Drill-and-fill and injection foam both access wall cavities through small holes from the exterior or interior. The openings are patched and photographed afterward. Cavity accessibility depends on framing type and existing obstructions.
Do pre-WWII Atlanta homes really have no wall insulation?
Most do not. Craftsman bungalows and foursquares built before 1940 in Atlanta’s intown neighborhoods used balloon or platform framing with empty stud cavities. The walls are open inside and lose heat and cooling through the framing itself. Call (218) 261-7714 for a written evaluation.
Attic Cleaning & Rodent Proofing in Atlanta
Attic cleaning and rodent proofing in Atlanta runs $1,500-$5,500 for a full cleanout, sanitizing, and exclusion package, depending on attic size and contamination level. Atlanta’s mature tree canopy over intown neighborhoods means squirrels and roof rats are a constant presence, and once they establish a nest in a bungalow attic, the droppings and urine soak into insulation and sheathing. Our Attic Cleaning & Rodent Proofing work removes the contaminated material, sanitizes the deck, seals every entry point from the exterior, and leaves you with a documented before-and-after record.
Attic Cleanout
Signs you need it
You see droppings, nesting material, or damaged insulation in the attic, or you hear scratching at dawn and dusk from above.
What it costs in Atlanta
Attic cleanout in Atlanta runs $1,500-$3,500 for a standard 1,200-2,000 sq ft attic, including debris removal.
How we do it
We remove contaminated insulation and debris, vacuum the deck, and document the cleaned surfaces with photos before any new insulation is installed.
Rodent Proofing & Exclusion
Signs you need it
Rodents keep returning despite previous trapping, or you’ve found entry points at roof returns, gable vents, or utility penetrations.
What it costs in Atlanta
Rodent proofing and exclusion in Atlanta runs $800-$2,500, combined with cleanout, depending on the number of entry points and roof access difficulty.
How we do it
We seal every entry point with metal mesh and foam where appropriate, document each sealing location with photos, and provide a written list of what was closed.
What Attic Cleaning & Rodent Proofing Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Attic cleanout | $1,500-$3,500 |
| Attic sanitizing and decontamination | $800-$1,800 |
| Rodent proofing and exclusion | $800-$2,500 |
Do I need to replace insulation after rodents in Atlanta?
Usually yes. Rodent urine and droppings soak into insulation and cannot be meaningfully cleaned. The contaminated material must come out, the deck sanitized, and new insulation installed only after exclusion is complete. Call (218) 261-7714 for a written evaluation.
How fast can you get rodents out of an Atlanta attic?
Exclusion and cleanout typically happen in one to two working days once the scope is written. Atlanta’s tree canopy means follow-up sealing is part of the job; we document every entry point we close and show you the photos.
Home Energy Audit in Atlanta
A home energy audit in Atlanta runs $349-$850 for a full blower-door, thermal imaging, and duct leakage assessment, and it’s the only way to know whether your house is losing conditioned air through the attic, walls, ducts, or all three. For Atlanta’s mixed-humid climate, the audit matters because you may be spending money cooling air that’s leaking straight out of a top plate or a disconnected duct boot before you ever notice the problem. Our Home Energy Audit service provides a prioritized, written list of findings, not a sales pitch.
Blower Door Test
Signs you need it
Rooms vary in temperature by 5°F or more, and energy bills climb during Atlanta’s cooling season despite consistent thermostat settings.
What it costs in Atlanta
A standalone blower door test in Atlanta runs $349-$550, including a written report of the CFM50 readings.
How we do it
We mount the blower door at an exterior entry, depressurize the house, and measure the air leakage in CFM50, recording the number you can compare against later.
Thermal Imaging Inspection
Signs you need it
You suspect missing or settled insulation in walls or ceilings but there’s no visible access to confirm it.
What it costs in Atlanta
Thermal imaging inspection in Atlanta runs $199-$400 when added to a blower door test.
How we do it
We scan walls, ceilings, and floors with a thermal camera, document the temperature variations, and cross-reference them with the blower-door readings in the written report.
What Home Energy Audit Costs in Atlanta
| Item | Typical range in Atlanta |
|---|---|
| Blower door test | $349-$550 |
| Thermal imaging add-on | $199-$400 |
| Full audit including duct leakage | $599-$850 |
What does a blower-door test actually tell me in Atlanta?
It gives one number, CFM50, that shows how much air your building envelope is losing under pressure. A typical Atlanta bungalow reads 3,500-5,000 CFM50 before any sealing. After sealing and insulation, the same house often reads 1,800-2,400. You keep the numbers.
Is an energy audit worth it before insulation in Atlanta?
Yes, because insulation without air sealing underperforms. The audit tells you where the leaks are and which fixes get you measurable results. If you already have a written estimate from another contractor, ask us for a free second opinion. Call (218) 261-7714.
Brands We Service in Atlanta
Our Atlanta crews work with insulation from Knauf, Rockwool, CertainTeed, and Icynene, among others. We stock common material locally and order project-specific product based on the written scope. No proprietary product lock-in. See our brands for the full list and what each material is best suited for in Atlanta’s climate.
Pricing for Insulation in Atlanta, GA
| Service | Typical range in Atlanta |
|---|---|
| Open-cell spray foam attic | $2.50-$4.50 per sq ft |
| Closed-cell spray foam attic | $4.00-$7.50 per sq ft |
| Blown-in cellulose attic | $1.75-$3.00 per sq ft |
| Blown-in fiberglass attic | $1.75-$3.50 per sq ft |
| Radiant barrier installation | $1.50-$4.50 per sq ft |
| Attic insulation removal | $2.00-$3.50 per sq ft |
| Attic air sealing | $1.00-$2.50 per sq ft |
| Wall insulation (drill and fill) | $2.50-$4.50 per sq ft |
| Attic cleanout | $1,500-$3,500 |
| Home energy audit | $349-$850 |
Prices in Atlanta push upward with attic access difficulty, steep roof pitches, rodent contamination, and the age of the framing you’re working around. Under The Haven Standard, every job gets a written price before work starts, a written scope, and a written warranty delivered before anyone lifts a tool. No open-ended estimates, no exceptions.
Neighborhoods We Serve in Atlanta
Our Atlanta crews work the full metro area, both intown and OTP. We regularly schedule in the bungalow belt and the surrounding suburbs, and dispatch is coordinated from the Atlanta office. Most neighborhoods can be scheduled within a few business days once the scope is written.
- Grant Park
- Virginia-Highland
- Candler Park
- Kirkwood
- Alpharetta
Service Area - Cities Near Atlanta
We work across the Atlanta metro and into surrounding municipalities. If you’re in Smyrna, GA, Marietta, GA, Roswell, GA, or Alpharetta, GA, the same written-price scope and documented record apply. Call (218) 261-7714 and a live person answers, 24/7.
Serving Atlanta, GA - Our Local Coverage Area
We’re based in the Atlanta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Atlanta
Most Atlanta jobs are scheduled within three to five business days of the written scope and price being agreed. Emergency situations like exposed attic floors after storm damage or rodent contamination can often be prioritized. A live person answers calls 24/7 at (218) 261-7714, no voicemail loops.
HOA rules generally do not restrict interior insulation, attic, or crawl space work in Atlanta. Exterior changes like visible vents or radiant barrier visible from the street may require architectural review in some neighborhoods. We’ll flag any exterior-facing scope in the written proposal so you can check before work begins.
Every Atlanta job closes with a Documented Photo Record showing the work completed, a written scope, and a written warranty under The Haven Standard. On applicable jobs, you also get before-and-after blower-door numbers showing the measured change in air leakage. Nothing is verbal, and everything is in the file you keep.
Ready to get a written price? Call Topside Attic Insulation at (218) 261-7714. We’ll write the scope, give you a flat price, and show you the numbers when the work is done.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 1-hour.
- 4You approve before work beginsNothing starts until you say go.
What Atlanta Customers Say
"Crawl space encapsulation done properly. Photographs of the vapour barrier at every seam, and the damp smell in the hallway is gone."
- Ainsley P."The winter gas bill dropped by about a third. They had estimated a quarter, so they under-promised."
- Genevieve R."Two other companies quoted to blow more insulation on top of what was there. These were the only ones who said the existing material had to come out first, and explained why."
- Clifford E.